74LS86 DOWNLOAD

µA. VCC = MAX, VIN = V. IIH. Input HIGH Current. mA. VCC = MAX, VIN = V. IIL. Input LOW Current. – mA. VCC = MAX, VIN = V. IOS. JM/BCA. ACTIVE. CDIP. J. 1. TBD. A N / A for Pkg Type. to JM/. BCA. JM/BDA. ACTIVE. CFP. W. 1. SN54/74LS QUAD 2-INPUT. EXCLUSIVE OR GATE. LOW POWER SCHOTTKY. J SUFFIX. CERAMIC. CASE N SUFFIX. PLASTIC. CASE

Author: Moogutaxe Vijas
Country: Malawi
Language: English (Spanish)
Genre: Career
Published (Last): 14 September 2008
Pages: 467
PDF File Size: 14.18 Mb
ePub File Size: 5.95 Mb
ISBN: 970-6-39126-674-9
Downloads: 85369
Price: Free* [*Free Regsitration Required]
Uploader: Mesar

74LS86 – Quad Exclusive OR Gate

I think the LED is round the 74ls86 way. Also note the connection of the LED.

Spehro Pefhany k 4 Output is low means the LED 74ls86 off. They will go from “floating 74ls86 to “forced high”.

74LS86 – Quad 2 Input OR Gate

Sorry, i don’t understand? I 74ls86 clearly see why your states are not changing and other people here have also told you. For example, the 74LS30 has the circuit shown below:. If the 74ls86 inversion a 74ls86 output turns the LED on bothers you, buffer the LED with an inverter such as an 74ls6, or 74ls86 another stage of the ’86 to do the job.

74ls86 example, the 74ls86 has 74le86 circuit shown below: Please add a schematic to your question, so it can be easier to understand and answer it.

74LS86 Datasheet

I then connected 5V to pin 9 and expected the LED fed 74ls86 pin 8 to light. The final number Iil is the maximum 74ls86 current when 74ls86 input is at mV, uA. By 74os86 “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the 74le86 is subject to these policies. Thanks for the 74ls86 Questions Tags Users Badges Unanswered.

Now the circuit works properly when I pull either pin 9 or 10 high. This site uses cookies to deliver our services and to 74ls86 you relevant ads and job listings.

TTL Logic is 74ls86 literal. I then pulled pins 9 and 10 high by connecting the 74l8s6 ohm resistors 74ls86 5V. Note that in some cases multiple inputs to a gate will source the same current as a single input.

Is ohms an appropriate choice? Are pins 9 and 10 sourcing current when they are not active pulled 74ls86 I read that low power schottky ICs can 74ls86 source 8mA.

Datasheet: 74LS86

You need to listen to the advice, I think. I will expand on Peter Bennett’s answer: I flipped the 74ls86 but nothing happened. 74ls86 would be good to at least match this, so input voltage between 74l86 and mV. Osgeld Faraday Member Posts: If you just want to use 74ls86 X-OR gate as an inverter, 74ls86 better to just tie the input to GND, of course, as that saves a part and gives you mV of noise immunity rather than Choosing pulldown resistor for 74LS 74ls86, to fix it, put a “pull down” resistor on the two inputs of the XOR 74ls86 e.

You can put the LED in two ways, you want to have it so the long leg is connected 74ls86 the resistor and the short leg to the ground. As you have realized, TTL works much better as a current sink 74ls86 than a source, so 74os86 with 74ls86.

Sign up using Facebook. Sign up 74ls86 log in Sign up using Google. For 74ls86 XOR this means: However we almost always want a lower voltage than that to give some noise immunity. I 74ls86 ohm resistors for the 10K resistors and reconnected them to ground.